He should use the thin alloy wire with a very low melting point. A fuse is designed to protect the circuit by melting and breaking the circuit when the current exceeds a safe limit. A thin alloy wire with a low melting point will melt quickly under excessive current, preventing damage to appliances. A thick copper wire has a high melting point and would not melt easily, failing to protect the circuit.
More Questions on Electricity: Magnetic and Heating Effects
1An electric bulb lights up when current passes through its filament, but the wires connecting the bulb to the power source do not glow significantly. Explain why.
→ 2Describe two distinct methods to increase the strength of an electromagnet created by winding an insulated copper wire around an iron core.
→ 3Assertion (A): An electric fuse is an important safety device in household circuits. Reason (R): It protects the circuit and appliances from damage by melting and breaking the circuit when excessive current flows.
→ 4A coil of wire is wound around an iron nail, and a current is passed through it. What would happen if the direction of current flowing through the coil is reversed?
→ 5Why is nichrome alloy commonly used for the heating elements in electric toasters and heaters, instead of pure copper?
→ 6Explain why using too many electrical appliances simultaneously connected to a single socket can be dangerous.
→ 7A student places a compass needle near a straight wire. When current flows from North to South through the wire, the North pole of the compass needle deflects towards the East. If the student reverses the direction of the current (South to North), how will the compass needle behave, and why?
→ 8Two wires, A and B, are made of the same material and have the same length. Wire A is thinner than wire B. If the same current is passed through both wires for the same duration, which wire will produce more heat and why?
→ 9Compare and contrast an electromagnet with a permanent magnet based on their strength and ability to be switched on/off.
→ 10Why is the fuse wire made of a material with a low melting point and high resistance?
→ 11An electric toaster has a heating element made of Nichrome wire. When it is switched on, it draws a current of 5 A from a 220 V supply. If the toaster is used for 1 minute, calculate the total electrical energy consumed and the heat produced in Joules.
→ 12A student sets up an experiment with a current-carrying wire placed above a compass. When the current flows from north to south, the compass needle deflects towards the west. What will happen to the compass needle if the student reverses the direction of current flow in the wire, and why?
→ 13Compare the primary use of the heating effect of electric current in an electric fuse with its primary use in an electric immersion rod. What is the key difference in how the heating effect is utilized in these two devices?
→ 14You are given an insulated copper wire, a battery, and an iron nail. Describe the steps to construct a simple device that can attract small paper clips, and explain the scientific principle behind its working.
→ 15A 100W light bulb and a 1000W electric heater are both connected to a 220V household supply. Which device draws more current from the supply, and how does this relate to the heat produced?
→ 16A domestic electrical circuit is designed to carry a maximum safe current. If multiple high-power appliances are switched on simultaneously, what dangerous phenomenon might occur, and how does a fuse help prevent serious damage?
→ 17A student winds insulated copper wire around an iron nail and connects the ends to a battery, creating an electromagnet. Which of the following modifications would result in a stronger electromagnet?
→ 18An electric fuse is an essential safety device in electrical circuits. Which of the following statements about an electric fuse is INCORRECT?
→ 19An electric crane uses a strong temporary magnet to lift and release heavy metallic objects in a scrap yard. Which type of magnet is used, and what is its crucial property that makes it suitable for this purpose?
→ 20Why is nichrome alloy preferred for making the heating elements of electric heaters, while copper wires are used for connecting electrical circuits?
→ 21Explain why a fuse wire has a low melting point and high resistance, and how these properties help in protecting electrical circuits and appliances.
→ 22A coil of wire designed for a room heater has a resistance R. If this coil is cut into two equal halves and only one half is used in the heater, how would the heat produced by the heater change, assuming it is connected to the same power supply?
→ 23In an electric bell, what is the primary role of the electromagnet when the switch is pressed, and how does it contribute to the bell ringing?
→ 24An electromagnet is constructed by winding 50 turns of insulated copper wire around an iron nail and connecting it to a 3V battery. To make this electromagnet stronger, which of the following changes would be most effective?
→ 25A household iron operating at 220V draws a current of 5A. A fuse of rating 7A is used in its circuit. If the iron is replaced by a high-power immersion heater drawing 10A current, what is the most likely outcome when the heater is switched on?
→ 26An electric heater consumes 1000 Joules of energy in 10 seconds when 5 Amperes of current flows through it. What is the resistance of the heater element?
→ 27You are given an unmarked bar magnet and an electromagnet with a switch. How would you differentiate between them without using any other external magnetic material?
→ 28Assertion (A): Electric fuses are used in household circuits to prevent damage to appliances. Reason (R): Fuses have a low melting point and high resistance wire that melts when excessive current flows through it.
→ 29An electric current is passed through a coil of wire wound around an iron nail. A compass needle placed nearby shows a deflection. If the number of turns in the coil is doubled, what will happen to the deflection of the compass needle, and why?
→ 30A student connects a thin copper wire and a nichrome wire, both of the same length and thickness, in series to a battery. After some time, which wire will get hotter and why?
→ 31When an electric bulb glows, both the heating effect and the magnetic effect of electric current are present. Describe how each effect is observed in a glowing incandescent bulb and state which of the two effects is primarily utilized for the bulb's intended function.
→ 32A current-carrying straight conductor is held vertically. A compass needle placed just below it points towards the East when the current flows upwards. If the current direction is reversed (flows downwards), in which direction will the compass needle (placed at the same position below the wire) point?
→ 33An electric immersion heater uses a specific heating element to warm water. If this heating element were accidentally replaced with an ordinary copper wire of the exact same length and thickness, what would be the most likely outcome when the heater is switched on, and why?
→ 34A student prepares two electromagnets. Electromagnet X is made by winding 60 turns of insulated copper wire around a soft iron core and connecting it to a 3V battery. Electromagnet Y is made by winding 120 turns of the same wire around an identical soft iron core and connecting it to a 1.5V battery. Which electromagnet would likely be stronger, and what is the primary reason for the difference in strength?
→ 35A fuse wire is an essential safety component in electrical circuits. Explain two critical properties a material must possess to be suitable for making a fuse wire and why these properties are vital for its protective function.
→ 36In an electric bell, an electromagnet attracts a soft iron armature, which then breaks the circuit to allow it to return. What would happen if the soft iron armature was replaced with a permanent magnet?
→ 37A kettle heater (resistance R1) and a hairdryer (resistance R2) are designed to work at the same voltage. If R1 is significantly smaller than R2, which appliance will produce more heat per unit time when switched on independently, and why?
→ 38A compass needle shows deflection when brought near a current-carrying wire, but this deflection disappears when the current is switched off. What does this observation tell us about the nature of the magnetic field produced by an electric current, compared to that of a permanent magnet?
→ 39An electric fuse is a critical safety device in household circuits. Explain two essential properties of the material used for making a fuse wire and why it is always connected in series with the appliance.
→ 40How would a student increase the strength of an electromagnet they have made using an iron nail, insulated copper wire, and a battery?
→ 41Describe two key differences between an electromagnet and a permanent magnet, highlighting their practical implications.
→ 42A device draws a current of 5 A under normal operating conditions. What would be the most appropriate fuse rating for this device in a household circuit, and why?
→ 43An electric toaster and an electric bulb are connected to the same household circuit. Why does the heating element of the toaster glow red hot, while the connecting wires of the circuit barely warm up, even though the same current flows through both?
→ 44A student creates an electromagnet by winding insulated copper wire around an iron nail. Which of the following actions would significantly increase the strength of this electromagnet?
→ 45Why is a fuse wire made of an alloy of lead and tin and not pure copper, even though copper is an excellent conductor?
→ 46An electric heater (1500 W), an electric kettle (1000 W), and a television (200 W) are all connected to the same 220 V household circuit. The circuit is protected by a 10 A fuse. What will happen if all three appliances are switched on simultaneously?
→ 47Which of the following statements correctly differentiates an electromagnet from a permanent magnet?
→ 48A fuse is an essential safety device in electrical circuits. Explain why a fuse wire is specifically designed to have a low melting point and a specific thickness, and how these properties help protect electrical appliances.
→ 49A student makes an electromagnet using a soft iron core, a coil of wire, and a battery. To make this electromagnet stronger, which change would be most effective?
→ 50Explain the working principle of an electric bell, focusing on how the magnetic effect of current is utilized to produce sound.
→ 51A student observes that when an electric current flows through a wire placed horizontally above a compass, the compass needle deflects towards the East. If the student reverses the direction of the current flow through the wire, what will happen to the compass needle?
→ 52Electric geysers and incandescent light bulbs both use the heating effect of electric current. However, the heating element in a geyser needs to reach a very high temperature to heat water, while the filament of an incandescent bulb needs to glow brightly. Explain one crucial difference in the material properties required for the heating element of a geyser compared to the filament of an incandescent bulb, keeping their primary functions in mind.
→ 53Which of the following modifications would result in an electromagnet with the LEAST magnetic strength?
→ 54A student connects an electric bell circuit. When the switch is pressed, the bell rings. If the student replaces the soft iron core inside the electromagnet of the bell with a wooden core, what is the most likely outcome when the switch is pressed again, and why?
→ 55During an experiment, a student finds that when a strong current is passed through a long, straight copper wire, a nearby compass needle deflects significantly. After some time, the wire also feels noticeably warm. Identify and explain the two effects of electric current demonstrated by these observations.
→ 56An electric heater and an electric bulb (filament type) are both connected to the same household power supply. Assuming both are working correctly, which appliance converts a larger proportion of electrical energy into heat and which converts a larger proportion into light? Explain why.
→ 57A student connects a small electromagnet to a battery. They observe that it can pick up 3 paper clips. To increase its lifting capacity to pick up 6 paper clips, which of the following changes would be most effective?
→ 58An electric fuse is designed to melt and break an electric circuit when an excessive current flows through it. Why is it that the main household wiring, through which the same current passes, does not melt under normal operating conditions, while the fuse wire does?
→ 59An electric crane uses an electromagnet to lift heavy iron scrap. After lifting, how does the crane release the scrap, and what principle of electromagnetism is crucial for this operation?
→ 60You have two insulated copper wires, P and Q, of the same length and material. Wire P is significantly thinner than Wire Q. If the exact same amount of electric current is passed through both wires for an equal duration, which wire will generate more heat, and what is the primary reason for this difference?
→ 61A student places a compass near a straight current-carrying wire. The compass needle deflects. If the student reverses the direction of current in the wire, what observation would be made, and why?
→ 62An electric bulb lights up instantly when switched on, but an electric iron takes a few minutes to heat up. Explain the primary reason for this difference in their working.
→ 63Consider a simple electromagnet made by winding insulated copper wire around an iron nail and connecting it to a battery. What would be the most effective way to temporarily increase the magnetic strength of this electromagnet?
→ 64A coil of wire in an electric heater heats up much more than the connecting wires, even though the same current flows through both. Explain why this phenomenon occurs.
→ 65Consider a long straight wire connected to a battery. A student brings a compass near the wire and observes a deflection. After some time, the student touches the wire and finds it warm. a) Identify the two effects of electric current demonstrated by these observations. b) Name one device that works solely based on the magnetic effect and one device that works solely based on the heating effect. c) How can the strength of the magnetic effect be increased without changing the current in the wire, and how can the heating effect be increased without changing the length of the wire?
→ 66Electric bells and cranes for lifting heavy iron scraps commonly use electromagnets instead of permanent magnets. Explain the key advantage of electromagnets that makes them suitable for these applications.
→ 67Assertion (A): A fuse wire is always connected in series with the live wire of an electrical circuit. Reason (R): It has a very high melting point and extremely low resistance to ensure that it does not melt during an overload.
→ 68Two electric heating coils, P and Q, are made of wires of the same material and length. Coil P uses a wire with a diameter of 1 mm, while Coil Q uses a wire with a diameter of 2 mm. If both coils are connected to the same voltage source for the same duration, which coil will produce more heat?
→ 69A compass needle points North when no current flows in a nearby wire. When a straight wire is held horizontally above the compass, aligned North-South, and current flows from North to South, the North pole of the compass needle deflects towards East. What would be the direction of deflection of the North pole if the wire is moved just below the compass, and the current direction remains North to South?
→ 70Consider two wires of the same length and thickness made of different materials: nichrome and copper. If the same amount of current is passed through both for the same duration, which wire would produce more heat, and why is this property important in practical applications?
→ 71A doorbell works using the magnetic effect of electric current. If the doorbell suddenly becomes very faint or stops working, which of the following changes is LEAST likely to be the direct cause related to its electromagnet?
→ 72A fuse wire is designed to protect electrical circuits. Why is it always connected in series with the live wire and made of a material with a low melting point and high resistance compared to the circuit wires?
→ 73A student wants to build a simple electromagnet to lift small iron pins. She has a copper wire, an iron nail, and a steel bar. Which combination would result in the strongest temporary electromagnet, and why?
→ 74A common household appliance uses a heating element made of a special alloy. If the appliance is designed to heat water quickly, what properties would be most desirable for the heating element's material and dimensions?
→ 75A student wants to increase the strength of an electromagnet. Which of the following actions would NOT contribute to increasing its strength?
→ 76A fuse is a critical safety device in electrical circuits. Explain the two main properties a fuse wire must possess to function effectively and why.
→ 77Which of these devices primarily operates based on the magnetic effect of electric current?
→ 78A coil of wire is connected to a battery. If the current flowing through the coil is doubled, how many times will the heat produced in the coil increase, assuming resistance and time remain constant?
→ 79Why is the core of an electromagnet typically made of soft iron instead of steel?
→ 80An electric bell rings when its circuit is closed. Explain the role of the electromagnet and the 'make-and-break' mechanism in the continuous ringing of the bell.
→ 81To make an electromagnet stronger, a student proposes four changes. Which of these changes would be LEAST effective in increasing the electromagnet's strength?
→ 82An electrician is wiring a new house and needs to choose materials for both the main connecting wires and the fuse wire. Why would he choose copper for connecting wires and an alloy like tin-lead for the fuse wire, despite both carrying current?
→ 83A compass needle is placed near a straight wire. When an electric current flows through the wire from north to south, the compass needle deflects towards the east. If the current direction is reversed to flow from south to north, in which direction will the compass needle deflect?
→ 84Why do the connecting wires in an electric circuit not glow red hot like the heating element of an electric heater, even when the same current flows through them?
→ 85An electric heater is rated 1500 W and operates on a 230 V supply. If the circuit supplying this heater is protected by a fuse rated at 5 A, what would happen if the heater is switched on, and why?
→ 86Identify two key differences in properties between an electromagnet (like one used in a scrapyard crane) and a permanent magnet (like one used to hold a refrigerator door closed), considering their respective applications.
→ 87A classroom demonstration circuit contains both a simple electromagnet and an electric fuse connected in series. Describe the primary effect of electric current observed in each component, and explain how the fuse ensures safety if the current unexpectedly becomes very high.
→ 88Why does the filament of an electric bulb glow brightly and heat up, while the copper connecting wires supplying current to it remain relatively cool?
→ 89A student makes an electromagnet using an iron nail, copper wire, and a battery. To significantly increase the lifting capacity of this electromagnet, what would be the most effective single change?
→ 90An electric circuit has two identical resistors, R1 and R2, connected in series to a battery. Another identical resistor, R3, is connected in parallel to the same battery. Which resistor (R1, R2, or R3) will dissipate the most heat, assuming they are all switched on for the same duration? Justify your answer.
→ 91Identify the primary physical effect of electric current (heating or magnetic) that is utilized in the functioning of the following devices: (i) Electric Bell (ii) Electric Heater (iii) Fuse (iv) Maglev Train
→ 92A student places a small compass needle near a straight copper wire. When an electric current flows from South to North in the wire, the North pole of the compass needle initially deflects towards the East. If the student reverses the direction of the current (now flowing from North to South), what will be the new direction of deflection of the North pole of the compass needle?
→ 93An electromagnet is constructed by winding insulated copper wire around an iron nail and connecting it to a battery. Which of the following actions would lead to a *decrease* in the strength of this electromagnet?
→ 94A homeowner observes that a new electrical appliance (e.g., an electric kettle) frequently blows the main fuse when switched on, even though other appliances in the house work fine. What is the most likely reason for this, and what action should the homeowner take?
→ 95A thick copper wire is used to transmit electricity from the main supply to your house, while a thin, high-resistance wire is used as a fuse in an electrical appliance. Explain the scientific reason behind these choices, referring to the heating effect of electric current.
→ 96Differentiate between a temporary magnet and a permanent magnet based on two key characteristics.
→ 97A household circuit is protected by an electric fuse rated 5 A. If two appliances, one drawing 3 A and another drawing 4 A, are switched on simultaneously in this circuit, what will most likely happen?
→ 98To make an electromagnet stronger, a student should:
→ 99An electric heater uses a coil of nichrome wire, not a straight copper wire, to produce heat. Explain two reasons why nichrome is preferred and why it is coiled.
→